Lcd Color Monitor
For More Lcd Color Monitor Info Click On The Blue Links Below
How do I match color that I see on-screen and color of printed output? I have LCD monitor & HP 1000 inkjet.?
My monitor is Viewsonic 19" LCD and printer is HP Business Inkjet 1000. Each time that I print color graphics, the colors in the printed output look different from those that are shown on the screen
Without buying a different printer, it's all related to ICC color profiling. Every printer will have a color profile that translates what's being displayed on the screen to the colors that printer needs to output. The software that came with the printer should have the color profile on it.
In display properties, click the settings tab, then advanced near the bottom. When the new window opens, there will be a color management tab. That will allow you to add color profiles. Now that you know where that is, contact HP to find out where the color profile is on their provided software, then browse for it using the instructions above. They might even walk you through it.
Repairing the DELL E153Fpc LCD Monitor with the complaint of display shutdown after few seconds (power LED still on) was not difficult. Normally when this type of problem happens, we would first suspect the inverter board, then the filter capacitors and lastly the main board. A defective in one of the lamps and a faulty TL1451AC PWM IC or inverter ic may caused the display to shutdown as well. If the lamp is defective, it will send a feedback to pin 3 or 14 of TL1451AC IC and caused it to stop producing output signal thus the display just shut off once you switch it on. The power board is using a SG6841D pwm ic and a FQPF7N80 power fet . If this power section blow, it is quite easy to troubleshoot because it has fewer components. You can also use other part numbers to substitute the power fet.
As usual, after opening up the cover, I would first check for any burnt components, loose connector, cracked board, dry joints and etc before doing the voltage test. As for the lamps, I would check it last because lamps were seldom spoilt. Upon scanning for any bad components before starting the voltage test, I found a filter capacitor that had turned into darker color. Using the ESR meter revealed the ESR ohm has shoot up to 12 ohms. This filter capacitor located at C922 with the value of 1000 micro farad 16 volt. If you donÂ’t have the ESR meter you can always use the digital capacitance meter. The value that I got from measuring the bad capacitor was 57 microfarad. If you donÂ’t have ESR meter, make sure you get one-itÂ’s fast and accurate.
Now, the question is why a filter capacitor can cause the display to shutdown? If you carefully see the picture, I’ve drawn the yellow path to show you how the voltage is flowing. By the way, the voltage at the bad filter capacitor line is 12 volt. The voltage passed through a SMD transistor in the start circuit and flow straight to pin 9 (VCC) of TL1451AC IC. In order to let the 12 volt to flow through the transistor and reach the vcc pin of the ic, first, a ‘on’ signal must be sent from the main board to trigger the transistor. If no signal send to the transistors (off signal), both transistors can’t be turned on and no voltage will follow through the ic. Thus if the main board or any of the start circuit components spoilt, there will be power but no display because the TL1451AC would not send signal to the Royer type L, C resonant and boost circuit, so no high voltage produced by the high voltage transformer and this will lead to no display.
In the above case, the LCD Monitor display shutdown was due to the ripple because of the bad filter capacitor. The ripple caused the TL1451AC IC to be unstable and eventually shutdown the output signal. Replacing only the filter capacitor solved the DELL E153Fpc LCD Monitor shutdown problem.
Conclusion, donÂ’t always presumed that LCD Monitor is very tough or difficult to repair. From the above article, you could see that the caused of the shutdown problem was only a bad capacitor. If you fully understood how LCD Monitor works, then chances for you to successfully repair the monitor is very high but again it depends on the availability of spare parts. If you ever come across any LCD Monitor sent to you for repair for the first time, go ahead and start troubleshoot it. Who knows one day LCD Monitor repair could become one of the major source of income to you and your business.
Jestine Yong is a electronic repairer and a writer, for more LCD Monitor repair secrets, please visit his website at http://www.electronicrepairguide.com/lcd-monitor-repair.html now.
Related posts
Tagged with: 7 tft lcd color monitor • arm electronics 7 lcd color monitor • calibration • color • Color Monitor • fpd1960 tft lcd color monitor pricing • gateway fpd1960 tft lcd color monitor • hardware • lcd • Lcd Color • Lcd Color Monitor • Lcd Monitor • monitor • pillow tft lcd color monitor • Power Led • tft lcd color monitor • tft lcd color monitor manual
Leave a Reply